|
Details for Customer
For
a V6 application, the engine mounts are used in conjunction with
original red motor 6cyl rubbers.
The engine bay harness is
connected to original loom under D/side dash and control loom is
mounted on D/side inner fender.
The E.C.M. is mounted on
the LHS kick panel or above the glove box.
Our loom is sold
on a changeover basis for the engine to computer loom.
If no
changeover loom is supplied, an additional cost of $200.00 will
apply.
Prices may vary slightly if an Ecotech engine is
used.
|
| LOOMEFI-01 | Engine Management loom to suit Holden Series 1 & 2 V6 Commodore Engines | $550 c/o | |
|
| LOOMEFI-08 | Engine Management loom to suit Holden V6 Ecotec Engines | $700 c/o | |
|
| MEMCAL-VT/V8 | Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. | $450c/o | |
|
| MEMCAL-VT/V6 | Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. | $450c/o | |
|
| MEMCAL-VR/V6 Man | Re-Programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit Conversion. | $450c/o | |
|
| MEMCAL-VR/V6 AUTO | Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. | $450c/o | |
|
| LOOMS/S-01 | Speed Sensor assembly & Loom with speedo cable provision. Suit T-700 Auto Trans. | $250 | |
|
| LOOMS/S-02 | Speed Sensor assembly & Loom with speedo cable provision. Suit T-350-400. Powerglide Auto Trans. | $200 | |
|
| B0580464070 | Hi-pressure EFI fuel pump | $195 | |  |
|
| BF-5030 | Hi-pressure fuel filter | $20 | | |
|
| 11004/KIT | Lift pump. Low pressure | $140 | | |
|
| ST-4 | EFI Surge Tank | $235 | | |
|
| FAN-EF4026 | 16'' 2100cfm UNIVERSAL FAN | $210 | |
|
| SUMP-04B | V6 Reversed Sump including Pickup | 550 c/o | |
|
| Error - No Match for SUMP-04A |
| CH-EM64 | COMMODORE V6 FITTEN TO HOLDEN GEMINI | $308 | |
|
| Error - No Match for XM-01 |
| A1158 | Transmission rubber mount to suit T350-T400-T700-Powerglide and T5 | $44 | | |
|
| CH-74 | HOLDEN GEMINI WITH V6 3.8 EFI COMMODORE ENGINE 3 INTO 1 DESIGN. 1 5/8'' (must use engine mounts EM-64) | $660 | | |
|
| CH-76 | HOLDEN TORANA LH-LX-UC & HQ-WB WITH V6 3.8 EFI COMMODORE ENGINE. 3 INTO 1 DESIGN. 1 5/8'' INCLUDES Y-PIECE (must use engine mounts CH-EM60) | $550 | | |
|
| SPEEDO-01 | Electronic Speedometer conversion. | $550 | |
|
| G/R-3/V6A | V6 3.8ltr Commodore Engine. Standard Replacement suit Auto | $180 | | |
|
| G/R-3/V6M1.9 | V6 3.8ltr Commodore Engine. Suit Manual trans. (10 Tooth pinion) | $350 | | |
|
| PULLEY-01 | Idler Pulley for Holden V6. Use as a replacement when not using Power Steering pump. | $270 | | |
|
All Prices in $Au
including GST. Overseas orders will be lower.
Back to the EFI wiring page
 -
|
)
)
)
)
)
'))
'))
)
'))
)